X2CrNiMo17-12-2/ 1.4404 / 316LLow-Carbon Molybdenum Austenitic Stainless Steel
What is 1.4404 (AISI 316L)?
X2CrNiMo17-12-2 (Werkstoff No. 1.4404, AISI 316L) is an austenitic stainless steel with 16.5–18.5% chromium, 10.0–13.0% nickel and 2.00–2.50% molybdenum, with carbon limited to ≤ 0.030%. Molybdenum raises resistance to pitting and crevice corrosion in chloride media compared with 304; the low carbon reduces the risk of intergranular corrosion after welding. Solution annealed (+AT) bar has Rp0.2 ≥ 200 MPa, Rm 500–700 MPa and elongation ≥ 40% (EN 10088-3, d ≤ 160 mm). It is used in chemical, pharmaceutical and food plants and for flanges and fittings.
Chemical Composition
Cast analysis, % by weight (per the applicable EN standard)
| Element | Range (%) |
|---|---|
| C | ≤ 0.030 |
| Si | ≤ 1.00 |
| Mn | ≤ 2.00 |
| P | ≤ 0.045 |
| S | ≤ 0.030 (EN 10088-3) · ≤ 0.015 (EN 10088-2) |
| Cr | 16.5–18.5 |
| Mo | 2.00–2.50 |
| Ni | 10.0–13.0 |
| N | ≤ 0.11 (EN 10088:2005) |
Mechanical Properties (+AT · EN 10088-3)
Values depend on ruling section / thickness (d).
| Section (mm) | Yield Re min (MPa) | Tensile Rm (MPa) | Elongation A min (%) |
|---|---|---|---|
| d ≤ 160 | 200 | 500–700 | 40 |
| 160 < d ≤ 250 | 200 | 500–700 | 30 |
Hardness: +AT (solution annealed): ≤ 215 HB (EN 10088-3). Cannot be hardened by heat treatment; it work-hardens during cold forming.
1.4404 / AISI 316L properties and use
International Equivalents
Values marked ≈ are nearest matches, not exact equivalents. Always confirm against the governing standard.
| System | Grade |
|---|---|
| EN | X2CrNiMo17-12-2 |
| W.-Nr. (DIN) | 1.4404 |
| AISI / UNS | 316L / S31603 |
| ASTM | A182 F316L · A276 · A240 |
| JIS | SUS316L |
| GOST | ≈ 03Х17Н14М3 (03Kh17N14M3) |
| AFNOR | Z3CND17-11-02 / Z2CND17-12 |
| BS (UK) | 316S11 |
| GB (China) | 022Cr17Ni12Mo2 |
Detailed comparison: 304 vs 316L · 316L vs 1.4404
Applications
- Chemical and petrochemical plants
- Pharmaceutical and medical equipment parts
- Food and beverage equipment
- Flanges, fittings and valve parts
- Heat exchangers and process piping
- Marine hardware (above-water service)
Available Product Forms
Product pages for this grade
- Stainless Steel BarsStainless Steel Round Bar
- Stainless Steel BarsStainless Steel Hexagon Bar
- Stainless Steel BarsStainless Steel Square Bar
- Stainless Steel BarsStainless Steel Flat Bar
- FlangesWeld Neck Flange
- FlangesSlip-On Flange
- FlangesBlind Flange
- FlangesThreaded Flange
- Pipe Fittings90° Elbow
- Pipe FittingsTee Fitting
Frequently Asked Questions
Are 316L and 1.4404 the same?+
In practice they are the ASTM/AISI and EN designations of the same material, but the ranges do not fully overlap: EN 1.4404 has Mo 2.00–2.50%, ASTM 316L 2.00–3.00%, and the Ni and Cr ranges differ slightly as well. See our 316L vs 1.4404 page for a detailed comparison. Dual-certified material is common.
What is the difference between 316 and 316L?+
316 (1.4401) is the version with carbon ≤ 0.07%; 316L (1.4404) limits carbon to ≤ 0.030%. Low carbon reduces chromium carbide precipitation during welding and lowers the risk of intergranular corrosion in welded parts. The F316/F316L dual certification common on flanges and fittings shows that the material meets the requirements of both grades.
1.4404 or 1.4571 (316Ti)?+
1.4571 is a molybdenum grade in which carbon is tied up (stabilised) by titanium; it is widespread in German-speaking markets. 1.4404 achieves the same aim by lowering carbon. In most aqueous corrosive media they behave similarly; titanium carbonitrides in 1.4571 limit polishability, so 1.4404 is usually preferred where a bright, polished surface is required. The project specification decides which one is used.
Can 316L be used in seawater?+
It is widely used for above-water and splash-zone hardware. However, when continuous seawater contact, stagnant water, crevices and elevated temperature combine, pitting and crevice corrosion can also occur on 316L. Under such conditions duplex (1.4462) or super-austenitic and super-duplex grades are considered.
Does Aktif Çelik supply 316L stainless bars?+
1.4401 / 316 round, hexagon, square and flat bars are supplied with an EN 10204 3.1 certificate; 1.4404 / 316L or dual-certified 316/316L material is quoted on request. Whether a given size is in stock, the minimum quantity and the lead time are stated in the quotation.
Looking for this steel grade?
Request a quote with your sizes, tolerances and delivery condition — we respond within 24 hours.
Related Tools
References & Standards
Values on this page are reference data compiled from the applicable EN standard; certified material properties are defined by the mill test certificate (EN 10204 3.1).
