Technical Specifications
Key Features
- No welding required
- Quick installation
- Suitable for hazardous areas
- Compact design
- Easy maintenance
- Low labor cost
Applications
- Fire-fighting networks
- Small-bore lines
- Instrumentation
- Temporary piping
- Non-sparking areas
- Air lines
Dimension Table
| Nominal Size | Outside Diameter (mm) | Thickness (mm) | Bolt Circle (mm) | No. of Bolts | Bolt Size |
|---|---|---|---|---|---|
| 1/2" | 89 | 11 | 60.3 | 4 | 1/2" |
| 3/4" | 99 | 13 | 69.9 | 4 | 1/2" |
| 1" | 108 | 14 | 79.4 | 4 | 1/2" |
| 2" | 152 | 19 | 120.7 | 4 | 5/8" |
| 3" | 191 | 24 | 152.4 | 4 | 5/8" |
Technical Notes
- 01Use thread sealant for leak-tight joints.
- 02Risk of loosening under high vibration.
- 03Requires periodic inspection and tightening.
- 04Threaded joints may weaken under temperature swings.
Threaded flange: joints without welding
A threaded flange has a tapered internal thread in its hub and is screwed onto an externally threaded pipe, so the joint is made without welding. This is useful in areas where hot work is restricted, on galvanized pipe whose zinc coating would be damaged by welding, and on small-bore utility lines that may be dismantled and rebuilt.
ASME B16.5 specifies threaded flanges with NPT threads to ASME B1.20.1; EN 1092-1 Type 13 uses pipe threads to ISO 7-1. In practice they are used in small sizes, typically up to NPS 4, and in Classes 150 and 300. Common materials are ASTM A105 for carbon steel and A182 F304L or F316L for stainless steel, usually with a raised face. Typical services are water, air, inert gas, fire-fighting systems and instrument connections.
Threaded joints can loosen or leak under vibration, thermal cycling or bending loads, so they do not suit high-temperature, cyclic or toxic service. A compatible thread sealant or tape is needed, and some specifications require a seal weld after assembly. Check that the pipe wall left under the thread is sufficient for the pressure; heavier schedules are often required. For welded small-bore systems compare with socket-weld fittings; for larger or critical lines use a weld neck flange.
Related products
Grade datasheets
Chemistry, mechanical properties and equivalents of the steel grades used for this product:
Grade comparisons
What is a weld neck flange?
A weld neck flange has a long tapered hub that is butt-welded to the pipe.
Flanges: guide and FAQGet a Quote
Contact our expert team for pricing and delivery information on this flange type.
Get a QuoteRelated Blog Posts
Technical articles, guides and industry analyses

A105 vs A350 LF2: Which Flange Material for Low Temperatures?
A105 and A350 LF2 are two forged carbon steels of the same strength; the real difference is impact testing. LF2 Class 1 is guaranteed by a notch impact test at −46 °C, while A105 has no mandatory impact test. Chemistry and mechanical table, the window that meets both standards, and a flange–pipe–fitting set by design temperature.

Matching Fittings and Flanges to Pipe Schedule: SCH 80, SCH 160, XXS
Schedule is the pipe's wall thickness; fittings and flanges carry the same information in different ways. On butt-weld fittings the schedule follows the pipe, on socket-weld and threaded fittings the class does, and on weld neck flanges the bore does. We put the matching rules for SCH 160 and XXS lines and our calculated weight table in one place.
