Quality & Certificates

EN 10204 certificates and how to read an MTR

Material conformity is proven by documentation. We agree which inspection document is required at order stage and manage the shipment accordingly.

  • EN 10204 2.1
  • EN 10204 2.2
  • EN 10204 3.1
  • EN 10204 3.2

Types of inspection document under EN 10204

EN 10204 defines the inspection documents supplied to the purchaser of metallic products. The difference lies in who validates the document and whether the results relate to the products actually delivered.

TypeDocumentValidated byContent
2.1Declaration of compliance with the orderManufacturerNo test results — a statement of compliance only
2.2Test reportManufacturerResults of non-specific inspection: products of the same production, not necessarily those delivered
3.1Inspection certificate 3.1Manufacturer's authorised inspection representative, independent of the manufacturing departmentResults of specific inspection on the delivered products or their test units
3.2Inspection certificate 3.2Manufacturer's authorised inspection representative and the purchaser's authorised representative, or the inspector designated by official regulationsResults of specific inspection on the delivered products

How we handle it

  • The required document is agreed at order stage, according to your specification.
  • Shipments are supplied with an EN 10204 3.1 inspection certificate; where the specification accepts it, a 2.2 test report can be supplied.
  • 3.2 certificates and third-party inspection by independent bodies such as SGS, Bureau Veritas or TÜV are arranged on request.
  • The scope of third-party inspection (e.g. test witnessing, dimensional and surface checks, pre-shipment inspection) is agreed with the order; state the requirement at quotation stage.
  • The certificate is issued by the producing mill; its heat number is traceable to the label on each bundle.

How to read a mill test certificate (MTR)

Layouts differ from mill to mill, but a 3.1 certificate almost always contains the same blocks:

  1. Header

    Document type (EN 10204 3.1), certificate number and date, and the issuing manufacturer.

  2. Order references

    Purchaser and order or contract number — they should match your purchase order.

  3. Product description

    Product form, dimensions, quantity or weight, steel grade and product standard, e.g. EN 10083-3 42CrMo4 +QT.

  4. Heat (cast) number

    The key to traceability. It must match the marking or label on the material.

  5. Chemical composition

    Ladle (cast) analysis in weight %; compare each element with the limits of the standard or order.

  6. Tensile test

    Yield strength (ReH or Rp0.2), tensile strength (Rm), elongation (A %) and, where required, reduction of area (Z %), with the test-piece position and direction.

  7. Hardness and impact

    Hardness (HB, HRC or HV) and Charpy impact energy in joules at the stated test temperature.

  8. Delivery condition and heat treatment

    Condition such as +A, +N or +QT, with heat-treatment parameters where reported.

  9. Additional inspections

    Ultrasonic testing, dimensional and surface inspection, grain size or inclusion rating — only if ordered.

  10. Declaration and signature

    Statement that the products comply with the order, with the name and signature of the authorised inspection representative; a 3.2 certificate also carries the signature of the purchaser's representative or the third-party inspector.

Checklist on receipt

  • The heat number on the certificate matches the marking on the material.
  • Grade, product standard and delivery condition are exactly those of your order.
  • Each chemical and mechanical value lies within the limits of the standard or your specification.
  • Mechanical values are checked against the right size range: in EN standards the required properties depend on the ruling section.
  • The document type (2.2, 3.1 or 3.2) is the one your order requires.
  • Certificate and delivery documents refer to the same order and quantity.

Ladle analysis is taken from the melt; a product (check) analysis on the finished product may deviate slightly. The permissible deviations are defined in the product standards.

Tests on request

If your specification requires them, the following tests can be arranged:

  • Chemical analysis (spectrometer)
  • Tensile, yield and elongation test
  • Hardness (HB / HRC / HV)
  • Charpy impact (including sub-zero)
  • Ultrasonic testing (UT)
  • Dimensional and surface inspection

This page explains EN 10204 in general terms; certificate layouts differ from mill to mill. The order specification and the certificate supplied with the material are binding.

Send us your requirements

Tell us the grade, size and quantity — our team will get back to you within 24 hours.