How to Read Steel Designations: EN 10027, AISI/SAE, JIS and GOST Explained
42CrMo4, 1.7225, 4140, SCM440 and 38KhM describe the same steel family. We decode the naming rules of EN 10027-1 and -2, AISI/SAE, JIS and GOST with examples, showing how to infer chemistry from a grade name and how to build cross-references between systems correctly.
📋 Datasheets for the grades used in the examples: 42CrMo4 → · C45 → · 16MnCr5 → · S355J2 → · 11SMn30 →
Why Does a Steel Name Matter?
A steel designation is a short technical summary of the material. A name written to EN 10027 tells you either the application and strength (S355J2) or the chemical composition (42CrMo4). The same steel goes by different names in different countries: 42CrMo4 / 1.7225 in Europe, AISI 4140 in the USA, SCM440 in Japan and, as the closest match in Russia and the CIS, 38KhM (38ХМ). A good share of quotation and ordering mistakes comes from assuming these names are identical. Knowing how to read them removes much of that risk from the start.
EN 10027-1: Names by Application (Group 1)
In this group, the name starts with a letter followed by a mechanical property value:
| Letter | Meaning | What the number shows | Example |
|---|---|---|---|
| S | Structural steel | Min. yield strength (MPa) for the smallest thickness | S235JR, S355J2 |
| P | Pressure-vessel steel | Min. yield strength | P265GH |
| L | Line-pipe steel | Min. yield strength | L360 |
| E | Engineering steel | Min. yield strength | E295, E335 |
| B | Reinforcing steel | Characteristic yield strength | B500B |
| D | Flat products for cold forming | Letter and number code | DC01, DX51D |
For structural steels, the symbols after the number give the impact toughness: JR = 27 J at +20 °C, J0 = 27 J at 0 °C, J2 = 27 J at −20 °C, K2 = 40 J at −20 °C. Additional symbols then describe the delivery condition; +N, for example, means normalized or normalized-rolled. So S355J2+N is a structural steel with at least 355 MPa yield strength, 27 J impact energy guaranteed at −20 °C, delivered normalized.
EN 10027-1: Names by Chemical Composition (Group 2)
Most steels used in machine building are named in this group. There are four sub-rules.
1. Unalloyed steels (Mn below 1 %): the letter C + carbon × 100. C45 means roughly 0.45 % carbon. A trailing E indicates a controlled maximum sulphur content (C45E); R indicates a specified sulphur range (C45R).
2. Low-alloy steels (each alloying element below 5 %) and unalloyed steels with Mn ≥ 1 %: carbon × 100, then the element symbols in decreasing order of content, and finally their mean contents multiplied by a factor. The factors are:
| Factor | Elements |
|---|---|
| 4 | Cr, Co, Mn, Ni, Si, W |
| 10 | Al, Be, Cu, Mo, Nb, Pb, Ta, Ti, V, Zr |
| 100 | Ce, N, P, S |
| 1000 | B |
With this rule, names decode easily:
- 42CrMo4 → 0.42 % C; Cr ≈ 4/4 = 1 % (standard range 0.90–1.20); Mo present, but its amount is not given in the name.
- 16MnCr5 → 0.16 % C; Mn ≈ 5/4 = 1.25 % (range 1.00–1.30); Cr present.
- 18CrNiMo7-6 → 0.18 % C; Cr ≈ 7/4 = 1.75 %; Ni ≈ 6/4 = 1.5 %.
- 11SMn30 → 0.11 % C; S ≈ 30/100 = 0.30 % — in other words, a free-cutting steel.
3. High-alloy steels (at least one element at 5 % or more): the letter X + carbon × 100 + symbols + the actual percentages of the elements. X5CrNi18-10 is an austenitic stainless steel with at most 0.07 % carbon, ~18 % Cr and ~10 % Ni — the AISI 304 family.
4. High-speed steels: HS + the percentages of W-Mo-V-Co. HS6-5-2 = about 6 % W, 5 % Mo, 2 % V.
EN 10027-2: The Material Number (W.-Nr.)
Every steel name also has a numerical counterpart: 1.XXXX. The first digit "1" stands for steel, the next two digits for the steel group, and the last two for the sequence number within the group. Groups worth remembering:
- 1.0xxx — unalloyed base and quality steels (C45: 1.0503, S355J2: 1.0577)
- 1.1xxx — unalloyed special steels (C45E: 1.1191)
- 1.2xxx — tool steels
- 1.4xxx — stainless steels (X5CrNi18-10: 1.4301)
- 1.5xxx–1.8xxx — alloy special steels (42CrMo4: 1.7225, 16MnCr5: 1.7131)
The number is language-independent; it stays the same in a German, Turkish or Chinese specification. Writing both the name and the number on an order is the safest approach.
AISI/SAE: The Logic of Four Digits
In the USA, carbon and low-alloy steels are written with four digits: the first two indicate the alloy family, the last two the carbon content (percent × 100).
| Series | Family | Example |
|---|---|---|
| 10xx | Plain carbon steel | 1045 (≈ 0.45 % C) |
| 11xx / 12xx | Resulphurized / resulphurized and rephosphorized free-cutting steel | 1215 |
| 41xx | Cr-Mo | 4140 |
| 43xx | Ni-Cr-Mo | 4340 |
| 51xx | Cr | 5115, 5140 |
| 61xx | Cr-V | 6150 |
| 86xx | Low Ni-Cr-Mo | 8620 |
When carbon exceeds 1 %, five digits are used (bearing steel 52100). An inserted B indicates a boron addition (10B21), an L a lead addition (12L14); a trailing H marks the version with a guaranteed hardenability band (4140H). Stainless steels use three-digit AISI series such as 304, 316 and 420.
JIS: Letters Give the Family, Digits Give the Carbon
JIS names identify the family by letters:
- S45C (JIS G 4051): carbon steel for machine structural use, ≈ 0.45 % C.
- SCr420, SCr440 are chromium steels; SCM415, SCM440 chromium-molybdenum steels; SNCM220, SNCM439 nickel-chromium-molybdenum steels (JIS G 4053). The last two digits give the carbon (× 100); the digit before them is a code for the alloy level.
- SS400 (JIS G 3101): general structural steel; here 400 is not carbon but the minimum tensile strength (MPa).
- SUS304 is stainless, SUJ2 a bearing steel, SKD11 a cold-work tool steel.
GOST: Digits Give the Carbon, Letters Give the Elements
In the GOST system used in Russia and the CIS (GOST 1050, GOST 4543), the leading digits give the carbon as percent × 100; the Cyrillic letters that follow indicate the alloying elements:
| Letter | Element | Letter | Element |
|---|---|---|---|
| Х (Kh) | Chromium | Г (G) | Manganese |
| Н (N) | Nickel | С (S) | Silicon |
| М (M) | Molybdenum | Ф (F) | Vanadium |
| Т (T) | Titanium | Ю (Yu) | Aluminium |
If no digit follows a letter, the element is present up to roughly 1.5 %; if there is a digit, it gives the approximate percentage. A trailing А marks a high-grade steel (low P and S). Examples: steel 45 (сталь 45) ≈ C45; 40Х (40Kh) = 0.40 % C + Cr; 40ХН2МА (40KhN2MA) = 0.40 % C, Cr, ~2 % Ni, Mo, high grade; 12Х18Н10Т (12Kh18N10T) = stainless steel with ~18 % Cr and ~10 % Ni, titanium-stabilized. General structural steels use names such as Ст3сп (St3sp), where "сп" (sp) denotes a killed steel.
Same Steel, Different Names: Cross-Reference Table
| EN name | Mat. No. | AISI/SAE | JIS | GOST ≈ |
|---|---|---|---|---|
| C45 | 1.0503 | 1045 | S45C | 45 |
| 42CrMo4 | 1.7225 | 4140 | SCM440 | ≈ 38ХМ |
| 34CrNiMo6 | 1.6582 | ≈ 4340 | ≈ SNCM447 | ≈ 38ХН3МА |
| 16MnCr5 | 1.7131 | 5115 | ≈ SCr415 / SCr420 | ≈ 18ХГТ |
| 20NiCrMo2-2 | 1.6523 | 8620 | SNCM220 | ≈ 20ХНМ |
| 100Cr6 | 1.3505 | 52100 | SUJ2 | ШХ15 |
| S355J2 | 1.0577 | — | ≈ SM490B | ≈ 09Г2С |
The "≈" sign matters: cross-reference tables show the closest grade; chemical ranges, mechanical values and hardenability bands may not be identical. Before accepting an equivalent grade for a critical part, put the chemistry and mechanical tables of both standards side by side. Our Grade Equivalents and Chemical Composition tools help with this; for the British BS 970 "EN" names, see our EN8, EN19, EN24 guide.
Practical Rules When Writing an Order
- Write the name, material number and standard together: 42CrMo4 / 1.7225 / EN 10083-3.
- Add the delivery condition: +QT, +A, +N (see delivery condition codes).
- If a name from another system is given (for example 4140), state clearly which standard's values are binding.
- Check that the inspection document (EN 10204 3.1) shows the name exactly as on the order (see how to read a 3.1 certificate).
Supply from Aktif Çelik
🔗 See also: Steel Equivalence Tables · AFNOR – EN steel equivalents · GOST – EN steel equivalents · JIS – EN steel equivalents · BS 970 – EN steel equivalents
Whatever system your specification is written in, send us the grade and the standard; at the quotation stage we clarify the grade and standard with you and, where needed, propose an equivalent grade. For carbon steel, hot rolled bars and bright steel, simply state the grade name and the standard: Request a quote for C45 →
Detailed Technical Info & Quotation
Contact our expert team for detailed technical documents, application recommendations, and custom dimension quotes on this topic.

