Bundles of steel bars and forged flanges on wooden pallets ready for export
ProductsGuide

HS Codes for Steel Products: A 6-Digit Guide

Aktif Çelik Teknik Ekip7 min read

The first six digits of any national tariff code are the World Customs Organization's Harmonized System (HS) code, identical in every country. We collected the 6-digit HS headings for steel bars, flanges, fittings, ferroalloys and cast products, plus the thresholds that decide alloy versus non-alloy steel. Final classification is your customs broker's call.

⚠️ Important note: This article explains only the 6-digit codes of the World Customs Organization (WCO) Harmonized System, for information. National 8–12-digit codes, duty rates and trade measures change frequently. Final classification and declaration are the responsibility of your customs broker.

What Is an HS Code?

The HS code (Harmonized System) is the international goods classification managed by the World Customs Organization and used by more than 200 countries and customs territories. The first six digits are the same everywhere. Each country adds its own subdivisions behind them; in Turkey, the national code is called GTIP (customs tariff statistical position):

SystemDigitsUsed by
HS (WCO)6All member countries — the common base
CN (Combined Nomenclature)8European Union
TARIC10EU (measures and duty breakdown)
GTIP12Turkey (first 8 digits aligned with the EU CN)
HTS10United States
TN VED EAEU10Eurasian Economic Union (Russia, Kazakhstan, etc.)

The WCO revises the HS roughly every five years; the edition currently in force is HS 2022, and the codes in this article follow it. Steel products are grouped in two chapters: Chapter 72 (iron and steel: pig iron, ferroalloys, semi-finished and rolled products) and Chapter 73 (articles of iron or steel: tubes, fittings, flanges, cast and forged articles).

The First Question: Alloy or Non-Alloy?

In Chapter 72, the same product — a hot-rolled round bar, say — falls under a different heading depending on the type of steel: non-alloy (7214), stainless (7222) or "other alloy" (7228). The distinction is made on the actual chemical composition, not on the grade name. Under Note 1(f) to Chapter 72, a steel that is not stainless counts as "other alloy steel" if it contains at least one of the following elements at or above the proportion shown:

ElementThreshold (% by weight)ElementThreshold (% by weight)
Al0.3Mo0.08
B0.0008Ni0.3
Cr0.3Nb0.06
Co0.3Si0.6
Cu0.4Ti0.05
Pb0.4W0.3
Mn1.65V0.1
Zr0.05Others (except S, P, C, N), each0.1

Stainless steel, in turn, is alloy steel containing by weight 1.2 % or less of carbon and 10.5 % or more of chromium (Chapter 72, Note 1(e)).

The practical consequences of these thresholds:

  • 42CrMo4 (Cr 0.90–1.20; Mo 0.15–0.30) and 16MnCr5 (Cr 0.80–1.10) are always alloy steel; bars fall under heading 7228.
  • C45 is usually non-alloy. But EN 10083-2 allows residual contents of up to 0.40 % chromium and 0.10 % molybdenum in C45. If a heat reaches 0.30 % chromium or 0.08 % molybdenum, that lot may count as alloy steel for HS purposes. That is why classification must follow the actual analysis on the inspection certificate (see how to read a 3.1 certificate).
  • Boron micro-alloyed steels may count as alloy because of the 0.0008 % boron threshold.
  • Resulphurized free-cutting steels such as 11SMn30 are non-alloy, but under the definition in the Chapter 72 subheading notes (S ≥ 0.08 %, Pb ≥ 0.1 % and so on) they fall into separate subheadings as free-cutting steel.

To check an analysis against these thresholds quickly, use our Chemical Composition tool; for the composition of the grades themselves, see the 42CrMo4, C45 and 11SMn30 datasheets.

6-Digit HS Codes by Product Group

ProductConditionHS (6 digits)Note
Non-alloy steel barForged only7214.10
Non-alloy steel barHot-rolled, free-cutting steel7214.30
Non-alloy steel barHot-rolled, round (other)7214.99Rectangular section: 7214.91 · ribbed (rebar): 7214.20
Non-alloy steel barCold-drawn, free-cutting steel7215.10
Non-alloy steel barCold-drawn / cold-finished (other)7215.50
Alloy steel barHot-rolled7228.30e.g. 42CrMo4, 16MnCr5, 100Cr6
Alloy steel barForged only7228.40
Alloy steel barCold-drawn / cold-finished7228.50
Stainless steel barHot-rolled, round7222.11Cold-finished: 7222.20
Flange (not stainless)—7307.91Stainless flange: 7307.21
Butt-welding fittings: elbow, tee, reducer, capNot stainless7307.93Stainless: 7307.23
Threaded elbows, bends and sleevesNot stainless7307.92Other threaded and socket-weld fittings usually 7307.99
Ferro-manganese (C > 2 %)—7202.11
Ferro-silicon (Si > 55 %)—7202.21
Ferro-chromium (C > 4 %)—7202.41
Pig iron (non-alloy, P ≤ 0.5 %)—7201.10
Steel shot (granules, grit)—7205.10
Grinding ballsForged, not further worked7326.11Cast grinding balls: 7325.91
Silica sand—2505.10Chapter 25

High-speed steel bars (7228.10) and silico-manganese steel bars (7228.20) also have their own subheadings. For the weight declaration, our Weight Calculator gives bar and tube weights.

Four Questions That Decide the Code

  1. Material: non-alloy, stainless or other alloy? (Based on the actual analysis.)
  2. Shape: bar, section, wire, flat product, tube or finished article?
  3. Working condition: hot-rolled, forged or cold-drawn — or machined, coated, turned into a part? The phrase "not further worked than…" in the Chapter 72 headings matters for exactly this reason; a bar machined into a specific part may move to Chapter 73 or to the machinery chapters.
  4. Cross-section and presentation: round, rectangular, ribbed; straight lengths or irregularly wound coils (7213 for non-alloy, 7227 for alloy)?

Why the Code Matters

  • Duties and trade measures: customs duties, anti-dumping and safeguard measures are applied at code level; a wrong code means a wrong duty or a missed quota.
  • Origin and movement certificates: preferential rules of origin work by code. In Turkey–EU trade, steel products covered by the European Coal and Steel Community (ECSC) arrangements are outside the customs union and traded under a separate free trade agreement; for these products the EUR.1 is used instead of the A.TR. The code tells you whether your product is covered.
  • CBAM: for exports to the EU, most iron and steel goods of Chapters 72 and 73 fall under the Carbon Border Adjustment Mechanism (CBAM), and coverage is determined by the CN code. The obligation lies with the EU importer; check the current list for every shipment.
  • Document consistency: the commercial invoice, packing list, certificate of origin and declaration must all use the same code and the same product description.

Commonly Confused Cases

  • Martensitic stainless is stainless, not "other alloy": grades such as X20Cr13 (≈ AISI 420) with 12–14 % chromium may look low-alloyed, but because they exceed the 10.5 % chromium threshold they fall under the stainless headings (7222 for bars).
  • Bearing and tool steels have no separate place at 6 digits: bars of 100Cr6 or of cold-work tool steel sit in the same HS subheading as other alloy steel bars (7228.30 when hot-rolled). The distinction may be made in national subdivisions such as the EU's 8-digit CN, so the last digits of the national code can differ by grade.
  • Cutting to length does not stop a bar being a bar; machining can: a bar cut to length usually stays in the same heading. Material that has been turned and drilled into the shape of a specific part, however, may be classified as an article rather than a bar.
  • Same product, different country, different final digits: even when the first six digits stay the same, the 8–10-digit code and the duty rate in the destination country differ from the Turkish GTIP; the buyer declares under its own country's tariff.

Practical Tips for the Right Code

  • Describe the product with grade, standard, delivery condition and size: for example "42CrMo4+QT, EN 10083-3, hot-rolled round bar Ø80 mm".
  • Send the inspection certificate to your customs broker before classification; the analysis decides alloy versus non-alloy.
  • In unclear cases you can apply for Binding Tariff Information — BTI in the EU, BTB in Turkey; the decision is binding on the customs administration concerned.
  • If one shipment contains several grades, split the lines by grade.
  • When the product group changes (from bars to flanges, for example), do not copy the code of the previous shipment; each line is assessed again on its own material, shape and working condition.
  • Use the code you received from your customs broker identically on the proforma, the invoice and the packing list; if the code changes, update all documents together.

Exporting with Aktif Çelik

🔗 See also: How We Work · Buyer FAQ

The shipping documents — commercial invoice, packing list, certificate of origin and the EN 10204 inspection document — are prepared together, and the product description includes grade, standard, delivery condition and size. The tariff code on the Turkish export declaration is set by the customs broker; classification in the destination country is decided by the buyer's customs broker. When you ask for hot rolled bars, flanges, fittings or ferroalloys, please include the destination country: Request a quote for A105 flanges →

Detailed Technical Info & Quotation

Contact our expert team for detailed technical documents, application recommendations, and custom dimension quotes on this topic.

Get a Quote