4140 vs 4340 Steel: The Nickel Difference and How to Choose
We compare 4140 and 4340 — whose closest EN grades are 42CrMo4 and 34CrNiMo6 — by nickel content, hardenability, toughness and cost, with EN 10083-3 strength values by section size.
📋 42CrMo4 (≈ 4140) Datasheet → · 34CrNiMo6 (≈ 4340) Datasheet → — chemical composition, section-dependent mechanical properties and international equivalents.
What Are 4140 and 4340?
Both are high-strength quenched-and-tempered steels; the defining difference is nickel:
- 4140 (closest EN grade 42CrMo4, 1.7225): chrome-molybdenum steel, no nickel. The economical workhorse. 4140 and 42CrMo4 are close counterparts, not identical grades — see our 42CrMo4 vs 4140 comparison.
- 4340 (closest EN grade 34CrNiMo6, 1.6582): chrome-nickel-molybdenum steel with 1.65–2.00% nickel. Premium, for highly stressed critical parts. 34CrNiMo6 has less nickel (1.30–1.70%) and more chromium (1.30–1.70%), so it is only close to 4340 — see our 34CrNiMo6 vs 4340 comparison.
In short: 4140 is economical high strength in medium sections, 4340 offers superior hardenability + toughness in large sections.
Chemical Composition
| Element | 4140 (%) | 4340 (%) |
|---|---|---|
| Carbon (C) | 0.38–0.43 | 0.38–0.43 |
| Manganese (Mn) | 0.75–1.00 | 0.60–0.80 |
| Chromium (Cr) | 0.80–1.10 | 0.70–0.90 |
| Molybdenum (Mo) | 0.15–0.25 | 0.20–0.30 |
| Nickel (Ni) | — | 1.65–2.00 |
Basis: SAE J404 / ASTM A29. To compare chemistry across grades, use our Chemical Composition tool.
Mechanical Properties (EN 10083-3, +QT)
SAE J404 and ASTM A29 specify only the chemical composition of AISI 4140 and 4340; they give no mechanical values. The strength values below therefore come from the closest EN grades in EN 10083-3, and they depend on the section size (d):
| Section d (mm) | 42CrMo4 Re min. / Rm (MPa) | 34CrNiMo6 Re min. / Rm (MPa) |
|---|---|---|
| d ≤ 16 | 900 / 1100–1300 | 1000 / 1200–1400 |
| 16 < d ≤ 40 | 750 / 1000–1200 | 900 / 1100–1300 |
| 40 < d ≤ 100 | 650 / 900–1100 | 800 / 1000–1200 |
| 100 < d ≤ 160 | 550 / 800–950 | 700 / 900–1100 |
| 160 < d ≤ 250 | 500 / 750–900 | 600 / 800–950 |
The Defining Difference: Nickel → Hardenability and Toughness
Nickel deepens hardenability and preserves toughness even at high strength levels:
- 4340, thanks to its nickel, hardens to the core even in very large sections and stays non-brittle even above 1200 MPa. That is why it is standard for aircraft landing gear, heavy drive shafts and highly stressed critical parts.
- 4140, being nickel-free, is more economical and offers an excellent strength/cost balance in medium sections; but the core will not fully harden in very large cross-sections.
To convert hardness values, use our Hardness Converter.
When to Choose Which?
Choose 4140 if:
- The part is medium-section and cost matters (gears, shafts, axles, dies, bolts)
- The 42CrMo4 values for your section are enough (for example Re ≥ 650 MPa and Rm 900–1100 MPa at 40–100 mm)
- Wide stock and short lead time are wanted
Choose 4340 if:
- A large section must harden to the core (heavy shafts, large gears)
- High strength AND high toughness together are required in a large section (for example Re ≥ 700 MPa at 100–160 mm, where 42CrMo4 reaches only 550 MPa)
- Fatigue and impact are critical (aerospace, defense, heavy industry)
Application Areas
| Sector | 4140 | 4340 |
|---|---|---|
| Aerospace & defense | General structural parts | Landing gear, critical drivetrain |
| Energy | Shafts, gears | Turbine/generator main shafts |
| Heavy machinery | Axles, shafts, dies | Large-section drive shafts |
| Oil & gas | Valves, fittings | Critical drilling components |
For cross-standard equivalents use the Steel Grade Equivalent tool; for the difference from 4140's lower-carbon "sibling" 4130, see our 4130 vs 4140 article. For the full standard-by-standard comparison of 34CrNiMo6 and 4340 see 34CrNiMo6 vs 4340; for how the required section changes the choice see Q&T steel selection by section size.
Supply from Aktif Çelik
At Aktif Çelik we supply 42CrMo4 (≈ 4140) and 34CrNiMo6 (≈ 4340) in hot-rolled bar, forged bar and bright bar forms across a wide diameter range, from stock or from production partners. With 3.1 certified, quenched-and-tempered or normalized options we recommend the most suitable grade for your project. Contact our team for technical consultancy and cut-to-length service.
Detailed Technical Info & Quotation
Contact our expert team for detailed technical documents, application recommendations, and custom dimension quotes on this topic.
