Steel Grade Datasheet

11SMnPb30/ 1.0718 / ≈ 12L14Leaded Free-Cutting (Free-Machining) Steel

Standard
EN ISO 683-4 / EN 10277
Delivery Conditions
+C, +SH, +SL
Density
7.85 g/cm³
W.-Nr.
1.0718

What is 11SMnPb30 steel?

11SMnPb30 (Werkstoff No. 1.0718, nearest US equivalent AISI 12L14) is a free-cutting steel that contains 0.20–0.35% lead on top of 0.27–0.33% sulphur. Lead strengthens the chip-breaking effect of the manganese-sulphide inclusions and acts as an internal lubricant in the cutting zone, so it machines faster, with less tool wear and a better finish than lead-free 11SMn30. Cold drawn (+C), its tensile strength ranges from 360 to 810 MPa depending on diameter. It is not intended for heat treatment or welding; it is chosen for machinability.

Chemical Composition

Cast analysis, % by weight (per the applicable EN standard)

ElementRange (%)
C≤ 0.14
Si≤ 0.05
Mn0.90–1.30
P≤ 0.11
S0.27–0.33
Pb0.20–0.35

Mechanical Properties (+C · EN 10277)

Values depend on ruling section / thickness (d).

Section (mm)Yield Re min (MPa)Tensile Rm (MPa)Elongation A min (%)
5 ≤ d ≤ 10440510–8106
10 < d ≤ 16410490–7607
16 < d ≤ 40375460–7108
40 < d ≤ 63305400–6509
63 < d ≤ 100245360–6309

Hardness: The standard (EN 10277) specifies tensile strength by diameter rather than hardness: +C Rm 360–810 MPa. Not intended for hardening by heat treatment.

11SMnPb30 / 1.0718 properties and use

11SMnPb30 is the leaded free-cutting steel covered by EN ISO 683-4 (hot rolled) and EN 10277 (bright, cold drawn). Its chemistry matches lead-free 11SMn30 except for the 0.20–0.35% Pb addition. It is used for high-volume turning on multi-spindle automatics and sliding-head (Swiss-type) CNC lathes. Cold-drawn (+C) properties depend on diameter: at 5–10 mm Rp0.2 is ≥ 440 MPa and Rm 510–810 MPa, while at 63–100 mm Rp0.2 is ≥ 245 MPa and Rm 360–630 MPa. Welding is not recommended because of the high sulphur and phosphorus, and the steel is not normally heat treated. Because it contains lead, in the EU it is used in RoHS- and ELV-regulated products under the exemption for machining steel with up to 0.35% Pb; check the scope and validity of the exemption for your end product. For a quotation, state the diameter or across-flats size, tolerance class (e.g. h9–h11 to EN 10278), length, quantity and surface condition (+C, +SH, +SL). Aktif Çelik reviews the request through its supply network and prepares a quote; the material can be requested with an EN 10204 3.1 inspection certificate.

Related technical article: 11SMnPb30

International Equivalents

Values marked ≈ are nearest matches, not exact equivalents. Always confirm against the governing standard.

SystemGrade
EN11SMnPb30
W.-Nr. (DIN)1.0718
AISI/SAE≈ 12L14 (≈ 12L13)
ASTMA108 (12L14)
JIS≈ SUM22L / SUM24L
AFNORS250Pb
BS (UK)≈ 230M07Pb
GB (China)≈ Y15Pb

Steel Equivalence Tables

Applications

  • Small parts mass-produced on automatic lathes
  • Screws, nuts, studs and fasteners
  • Hydraulic and pneumatic fitting bodies
  • Bushings, pins and spacers
  • Connector and instrument parts
  • Short, lightly loaded shafts

Frequently Asked Questions

What is the difference between 11SMnPb30 and 11SMn30?+

Their C, Mn, P and S ranges are identical; 11SMnPb30 additionally contains 0.20–0.35% lead. Lead improves machinability: higher cutting speed with the same tool, shorter chips and a smoother surface. Where lead is not accepted, 11SMn30 or variants with tellurium or bismuth additions are used.

Is 11SMnPb30 the same as AISI 12L14?+

Not exactly, but it is the nearest equivalent. 12L14 is also a leaded, resulphurised free-cutting steel (ASTM A108), but its Mn and P ranges differ slightly from the EN values. The Japanese equivalent is SUM22L/SUM24L and the French one S250Pb. The order should state which standard applies.

Can 11SMnPb30 be welded or hardened?+

Welding is not recommended because of the high sulphur and phosphorus; the risk of cracking in the weld is high. With ≤ 0.14% carbon it does not harden on quenching. If a wear-resistant surface is needed, choose a case-hardening steel (16MnCr5); if strength is needed, a Q&T steel (C45, 42CrMo4).

Is leaded steel RoHS compliant?+

The EU RoHS Directive grants an exemption for lead as an alloying element in steel for machining purposes up to 0.35% by weight, and the ELV Directive contains a similar exemption. The maximum Pb content of 11SMnPb30 is 0.35%. Because the scope and duration of exemptions vary by product group, check the regulations that apply to your end product.

Looking for this steel grade?

Request a quote with your sizes, tolerances and delivery condition — we respond within 24 hours.

Request a Quote

Related Tools

Values on this page are reference data compiled from the applicable EN standard; certified material properties are defined by the mill test certificate (EN 10204 3.1).